Unbox the Machine
| Model | [•] Hylo™ | ||
| Category | [•] Installation | [ ] Operation | [ ] Maintenance |
Summary
The procedures that follow gives instructions on how to:
- Unbox the Hylo™ machine from the crate.
- Move the machine to its designated work location.
Estimated time: 45 minutes
Tools
| Qty | Description | Specification |
|---|---|---|
| 1 | Camera, Digital | N/A |
| 1 | Step Ladder | 3 steps, minimum top step height 26 in |
| 1 | T-Handle Key | 8 mm hex size |
| 1 | Wrench | 7/8" Size, 6-3/8" overall length |
| 1 | Wrench | 15/16" Size, 6-7/8" overall length |
Parts Information
None required.
Personal Protective Equipment
| Qty | Description | Minimum Specification |
|---|---|---|
| 1 | Safety Eyewear | ANSI/ISEA Z87.1 |
| 1 | Safety Footwear | N/A |
| A/R | Gloves | Work |
Examine the Shipping Indicators
The AON3D warranty will come in effect upon the date of reception of the machine. In order for AON3D to respect this warranty, the customer must provide clear photographs of the ShockWatch® 2 and the two TiltWatch® Plus indicators to our Customer Success team at help@aon3d.com. Make sure that your Reception Department (Shipping & Receiving) has been made aware of the importance of providing our Customer Success team with above-mentioned photographs.
- Examine the ShockWatch® 2 indicator, found on the rear panel of the shipping crate.
- Take a clear photograph of the ShockWatch® 2 indicator and note if one of the two top and/or bottom windows are red.
- Examine the two TiltWatch® Plus indicators located on the crate’s exterior panel.
- Take a clear photograph of the two TiltWatch® Plus indicators and note if a tilt greater than 30 degrees has been recorded.
- Send photographs of all three indicators to our Customer Success team at help@aon3d.com.
If either of the ShockWatch® 2 indicator windows are red, and/or if either one of the two TiltWatch® Plus indicators show(s) a tilt greater than 30 degrees, the machine may have been damaged in transit. Reach out to our Customer Success team at help@aon3d.com.
Remove the Crate Panels
Keep the crate in storage for a minimum of 90 days. After the minimum period, the user may dispose of the crate according to local regulations.
One of the side panel changes into a ramp to help with the removal of machine from its platform.
-
Remove the metal clip removal tool found on the side panel of the crate.
Make sure unloading area is clear before the removal of the metal clips. The metal clips can fly away from the crate when removed. Failure to clear the work area can result in personal injury.
-
Remove the 32 metal clips and the five panels in the sequence that follows:
- Remove the ten metal clips that hold the top panel (1) to the front (5), rear (7) and side panels (2 & 6). Remove the top panel (1).
- Remove the eight metal clips that hold the ramp side panel (2) to the front (5) and rear (7) panels and to the crate platform. Remove the ramp side panel (2).
- Use the side panel (2) as ramp. Put the ramp on the floor and onto the two hinges of the crate platform (8).
- Unfold the metal plate (3) at the end of the ramp (2).
- Remove the two wooden pieces (4) between the front (5) and rear panels (7).
- Remove the five metal clips that hold the front panel (5) to the side panel and to the crate platform (8). Remove the front panel (5).
- Remove the five metal clips that hold the rear panel (7) to the side panel (6) and to the crate platform (8). Remove the rear panel (7).
- Remove the two metal clips that hold the side panel (6) to the crate platform (8). Remove the side panel (6).
If the clip removal tool is not available, a claw hammer can be used to remove the clips.
Remove Machine from the Crate
Always use a minimum of three persons for the procedure that follows. The machine weighs in excess of 350 kg (770 lbs.) and can cause injury, and/or damage equipment, if control is lost when the machine is moved.
- Use the wrenches to raise the four machine leveling feet. The wrenches are located in the front drawer of the machine.
- Carefully move the machine over the ramp and onto the floor.
- Use one person on the front of the machine and one person on the back of the machine to guide it.
- Use one person in the opposite side of the ramp to push the machine over the ramp.
- Move the machine to its designated work location.
Remove Packages
- Remove the packages inside the machine chamber under the vacuum chuck.