Power Requirements

The customer is responsible to make sure that all necessary electrical work is done by a licensed electrical contractor in accordance to their local laws and/or regulations.

Required Electrical Specifications, AON M2+ (CE)

Specification Value
Voltage 208-230 VAC, 1-phase (L1, L2/N)
Frequency 50/60 Hz
Amperage 24.5 A
Short-circuit current rating (SCCR) 5 kA
Maximum system impedance for phase A Z-phase A = 0.099 Ohm + j 0.062 Ohm
Maximum system impedance for neutral A Z-neutral A = 0.066 Ohm + j 0.041 Ohm
Power Cord 120 in. cable, bare wires (integrated)

There is no plug for the M2+ (CE). The integrated power cable for the AON M2+ (CE) ends with bare wires.

A supply disconnecting device shall be provided for the M2+ (CE) machine, for example:
• a switch-disconnector, with or without fuses, in accordance with IEC 60947-3, utilization category AC-23B or DC-23B.
• control and protective switching device suitable for isolation, in accordance with IEC 60947-6-2.
• a circuit-breaker suitable for isolation in accordance with IEC 60947-2.
• any other switching device in accordance with an IEC product standard for that device and which meets the isolation requirements and the appropriate utilization category and/or specified endurance requirements defined in the product standard.

An overcurrent protection device must be provided for the M2+ (CE) machine, either a fused device or a circuit breaker. AON3D recommends sizing the overcurrent protection device to interrupt the circuit at 30A.

Required Electrical Specifications, AON M2+ (R-NZ)

Specification Value
Voltage 208-230 VAC, 1-phase (L1, L2/N)
Frequency 50/60 Hz
Amperage 24.5 A
Short-circuit current rating (SCCR) 5 kA
Maximum system impedance for phase A Z-phase A = 0.099 Ohm + j 0.062 Ohm
Maximum system impedance for neutral A Z-neutral A = 0.066 Ohm + j 0.041 Ohm
Power Cord 82 in. Power Cord , 30 A, L6-30P (integrated)

Do not use power cord(s) other than the unit(s) supplied with the AON3D machine. Always use a grounded three-prong power outlet for AON M2+ (R-NZ), AON M2+, AON-M2 2020 and AON-M2 machines.

Required Electrical Specifications, AON M2+

Specification Value
Machine Circuit
Voltage 200-240 VAC, 1-phase (L1, L2/N)
Frequency 50/60 Hz
Amperage 18 A
Power Cord 120 in. Power Cord, 20 A, 12 AWG, IEC-320-C19 to NEMA L6-20P
Vacuum Circuit
Voltage 120 VAC
Frequency 50/60 Hz
Amperage 5 A
Power Cord 120 in. Power Cord, 10 A, 18 AWG, IEC-320-C13 to NEMA 5-15P

Do not use power cord(s) other than the unit(s) supplied with the AON3D machine. Always use a grounded three-prong power outlet for AON M2+ (R-NZ), AON M2+, AON-M2 2020 and AON-M2 machines.

Required Electrical Specifications, AON-M2 2020 and AON-M2

Specification Value
Voltage 208-230 VAC, 1-phase (L1, L2/N)
Frequency 50/60 Hz
Amperage 16 A
Power Cord 120 in. Power Cord, 20 A, 12 AWG, IEC-320-C19 to NEMA L6-20P

Do not use power cord(s) other than the unit(s) supplied with the AON3D machine. Always use a grounded three-prong power outlet for AON M2+ (R-NZ), AON M2+, AON-M2 2020 and AON-M2 machines.


Last modified: January 19, 2023